4.5″ FINDER MAX Series Diamond Blade – 115mm Dry Cutting Blade for Concrete, Brick and Masonry

4.5″ FINDER MAX Series Diamond Blade – 115mm Dry Cutting Blade for Concrete, Brick and Masonry

The 4.5″ FINDER MAX Series Diamond Blade is a 115mm diamond cutting blade designed for dry cutting applications involving concrete, brick, block and masonry materials. The blade is marked with a 4.5″ / 115mm diameter, 1.2mm thickness, 7.5mm segment specification, 22.23mm bore and maximum speed of 13,200 rpm, making it a practical cutting accessory for compatible angle grinders and circular saws. Pasted markdown

What Is the 4.5″ FINDER MAX Series Diamond Blade?

The 4.5″ FINDER MAX Series Diamond Blade is a diamond blade designed for cutting hard construction and masonry materials. The packaging identifies it as part of the FINDER MAX Series and specifies a 115mm blade diameter with a 22.23mm bore. It is marked for dry use only, meaning the packaging specifically instructs users not to use it with water. Pasted markdown

The blade is intended for cutting applications involving materials identified on the packaging, including concrete, brick, block and masonry. This makes it relevant to construction workers, masons, contractors, fabricators, installers, maintenance teams and other users who need a compact diamond blade for compatible cutting work.

Its compact 4.5-inch format makes it suitable for compatible handheld cutting equipment where a 115mm blade is required.

4.5″ and 115mm: Understanding the Size

The product is identified as 4.5 inches on the packaging and also specifies 115mm. These refer to the blade diameter.

The packaging provides the following specification:

The product information supplied does not provide a detailed diamond concentration, bond composition, exact segment construction, cutting depth or material-specific service life. These specifications should therefore not be assumed. Pasted markdown

What Materials Can the Diamond Blade Cut?

The packaging identifies the blade for materials including concrete, brick, block and masonry. This is important because a diamond blade should be selected according to the material it is intended to cut.

Concrete Cutting

Concrete is one of the main applications identified for this blade. Contractors and construction workers can use a compatible 115mm diamond blade for suitable concrete cutting tasks.

Applications may include construction adjustments, repair work, installation preparation and other projects where controlled cutting of concrete is required.

The exact cutting capacity depends on the machine, material, cutting conditions and installation.

Brick Cutting

The packaging also identifies brick as an applicable material. This makes the blade relevant to masonry work where bricks need to be cut to size.

Brick cutting can arise during building construction, renovation, openings, repairs and installation work.

Block Cutting

Concrete or masonry blocks may also require cutting during construction. A diamond blade designed for compatible block-cutting applications can provide a suitable option for contractors working on these materials.

Masonry Cutting

The product is also positioned for masonry-related cutting. Masonry work can involve different materials and densities, so users should always assess the actual material before beginning work.

Dry Diamond Blade: What Does Dry Cutting Mean?

One of the clearest instructions on the product packaging is DRY, and the warning specifically states for dry use only and not to use with water. Pasted markdown

This means the blade should be operated according to the manufacturer’s stated dry-cutting instruction rather than being combined with a water-cooling method.

For buyers searching for a dry diamond blade in Ghana, this is an important specification to understand. Dry cutting can be convenient for portable construction work because it does not require a water supply at the cutting location.

However, dry cutting can generate dust and heat. The packaging therefore provides safety instructions concerning protective equipment, blade speed and cooling. Users should follow the product instructions and the operating requirements of the machine being used.

Maximum Speed: 13,200 RPM

The packaging specifies a speed of 13,200 rpm. Pasted markdown

This is an important specification when selecting a machine for the blade.

Users should ensure that the compatible cutting machine does not operate outside the blade’s stated maximum speed. The blade should also be installed correctly and securely before operation.

The maximum speed should not be interpreted as a recommended speed for every material or every machine. The actual operating procedure should follow the blade and power-tool manufacturer’s instructions.

22.23mm Bore for Machine Compatibility

The blade has a stated 22.23mm bore. Pasted markdown

The bore is the centre hole through which the blade mounts onto the compatible machine.

This is one of the most important dimensions to check before purchasing a diamond blade. A blade may have the correct outer diameter but still be unsuitable if the bore or mounting arrangement does not match the machine.

The packaging illustrates compatible machines including an angle grinder and a circular saw. Users should still confirm compatibility with their particular machine before installation. Pasted markdown

1.2mm Blade Thickness and 7.5mm Specification

The front packaging identifies the specification as 115 × 1.2 × 7.5 × 22.23. Pasted markdown

These markings provide important dimensional information associated with the blade.

For buyers comparing a 115 diamond blade, checking the complete specification is more useful than looking only at the diameter. The 115mm size identifies the blade diameter, while the other measurements provide additional information relevant to compatibility and cutting configuration.

When ordering replacement blades, compare the complete specification against the existing blade and the tool manufacturer’s requirements.

Why Use a Diamond Blade for Masonry Cutting?

Diamond blades are used for cutting hard materials where a suitable abrasive or cutting configuration is required.

For construction users, having a dedicated diamond blade can help match the cutting accessory to the material rather than using an unsuitable general-purpose cutting disc.

The FINDER MAX Series blade is specifically identified for concrete, brick, block and masonry applications. Pasted markdown

This makes it relevant to construction and renovation tasks where these materials need to be cut.

Practical Applications in Ghana

The 4.5″ FINDER MAX Series Diamond Blade can be relevant to a wide range of construction and maintenance activities in Ghana.

Building Construction

Construction workers may require diamond blades when making suitable cuts in masonry materials during building projects.

The 115mm size provides a compact option for compatible handheld equipment.

Renovation and Property Maintenance

Renovation work can involve modifying existing brick, block or concrete components. A suitable diamond cutting blade can form part of a contractor’s cutting-tool setup.

Electrical Installation

During some construction and installation projects, masonry may need to be cut or modified to accommodate compatible building-service installations.

The exact application should be determined by the project requirements and the material being cut.

Plumbing and Building Services

Building-service contractors may encounter masonry cutting requirements during installation and renovation work. The blade can be considered where the material and machine are compatible with its stated specifications.

Masonry Work

Masons and building contractors can use appropriate diamond blades when cutting compatible brick and block materials.

Workshop and Maintenance Work

Maintenance teams may need cutting accessories for repair and modification work involving masonry materials.

The blade can be stored as part of a broader cutting-tool inventory for appropriate jobs.

Who Can Use This Diamond Blade?

The product can be relevant to:

The operator should have the appropriate knowledge and equipment for the cutting task and should follow the blade and machine safety instructions.

Diamond Blade Safety Instructions

The product packaging provides several important warnings. It states that the blade is for dry use only, instructs users to wear PPE including a face shield, respirator and gloves, and advises keeping the blade at full speed while avoiding lateral pressure. It also instructs users to allow the blade to run freely in air after cutting so it can cool naturally. Pasted markdown

These instructions should be taken seriously.

Wear Appropriate Protective Equipment

The packaging specifically depicts and mentions protective equipment. Depending on the work environment and applicable workplace requirements, appropriate eye, face, respiratory, hand and other protection should be considered.

Avoid Lateral Pressure

The packaging specifically warns against lateral pressure. The blade should be used for its intended cutting action rather than being forced sideways.

Do Not Use Water

The packaging explicitly states that the blade is for dry use only and should not be used with water. Pasted markdown

Allow the Blade to Cool

The packaging advises allowing the blade to run freely in air after cutting so it can cool naturally. Pasted markdown

Keep Children Away

The packaging also states that the product should be kept out of reach of children. Pasted markdown

Common Mistakes When Buying a Diamond Blade

Choosing the Wrong Diameter

A 115mm blade should not be purchased for a machine that requires another diameter unless the machine manufacturer specifically permits that configuration.

If you are searching for a diamond blade 300mm, 350mm diamond blade, 14 diamond blade, or 16 diamond blade, these refer to different size categories and should not be confused with this 115mm blade.

Ignoring the Bore Size

The bore is 22.23mm. Always check this against the machine’s mounting requirements. Pasted markdown

Using Water With a Dry-Use Blade

This product is clearly marked for dry use only. Adding water contrary to the product instruction is a mistake.

Exceeding the Stated Speed

The blade is marked with a maximum speed of 13,200 rpm. Users should ensure the machine and blade combination is operated within the applicable manufacturer’s requirements. Pasted markdown

Applying Excessive Side Pressure

The packaging specifically warns against lateral pressure. The blade should be allowed to perform its intended cutting action rather than being forced sideways.

4.5″ Diamond Blade Versus Other Diamond Blade Sizes

The right blade size depends on the machine and application.

A 4.5″ diamond blade is approximately 115mm in diameter, which is the specification of this FINDER MAX Series product.

Other search terms such as 125mm diamond blade, 14 diamond blade, 16 diamond blade, diamond blade 300mm and 350mm diamond blade describe different diameter categories.

A 125mm blade, for example, should not automatically be substituted for a 115mm blade simply because the sizes appear close. Compatibility with the machine is essential.

Other Diamond Blade Types and Search Terms

Customers researching diamond cutting products may encounter several related terms.

A turbo diamond blade generally refers to a blade design associated with a continuous or segmented turbo-style cutting edge. This product is identified specifically as a FINDER MAX Series Diamond Blade, so buyers should not assume it is a turbo diamond blade unless the product specification states that.

A general purpose diamond blade may be marketed for multiple compatible materials, while a material-specific blade may be selected for a particular cutting requirement.

A diamond blade for cutting marble is intended for a different material application. Likewise, a diamond blade for cutting steel should not be assumed to be equivalent to a masonry diamond blade.

The FINDER MAX Series blade shown here is identified for concrete, brick, block and masonry applications. Pasted markdown

What About Bosch Diamond Blades and Other Brands?

Buyers may compare the FINDER blade with products such as a Bosch diamond blade or other brands available in Ghana.

Brand comparison should be based on the actual requirements of the project, including:

A different brand should not be selected solely because it has a familiar name. The technical specification needs to match the intended machine and material.

Can a Diamond Blade Be Sharpened?

The search term diamond blade sharpener is sometimes used by buyers looking for ways to restore cutting performance.

However, the supplied information does not provide instructions for sharpening this particular FINDER MAX Series blade. Users should not assume that a specific sharpening procedure is approved for this product.

If cutting performance changes, inspect the blade and review the manufacturer’s instructions rather than applying an unverified sharpening method.

Buying a 4.5″ Diamond Blade in Ghana

If you are searching for a 4.5″ diamond blade for sale in Ghana, the first step is to confirm that 115mm is the required blade diameter for your machine.

Then check the bore, speed and intended material.

For this product, the key specifications shown on the packaging are:

These details are visible on the product packaging. Pasted markdown

Bulk Diamond Blade Supply in Ghana

Contractors, construction companies, maintenance departments, hardware retailers and other commercial buyers may require diamond blades in quantities rather than purchasing one at a time.

For bulk diamond blade supply in Ghana, buyers should provide the required diameter, bore, application, quantity and machine information where possible.

This makes it easier to source the correct blade rather than ordering based only on a general description such as “diamond cutting blade.”

CETECH Ghana supports individual customers, businesses, contractors, technicians, institutions, commercial buyers and industrial buyers. The company operates both online and through physical offline stores in Ghana, with support for bulk supply, industrial sourcing, consultation and related supply requirements where applicable. Pasted markdown

Why Buy the FINDER MAX Series Diamond Blade From CETECH Ghana?

CETECH Ghana provides construction, hardware and industrial products for customers who need practical solutions for projects, maintenance and everyday work.

For a customer looking for a diamond blade supplier in Ghana, having access to the product specification is important. CETECH can serve customers who need individual products as well as businesses, contractors and other buyers sourcing products for larger requirements. Pasted markdown

Customers can purchase through CETECH Ghana’s online and physical store channels, subject to availability. Bulk buyers can also enquire about supply requirements when purchasing multiple units.

Frequently Asked Questions

What size is the FINDER MAX Series Diamond Blade?

The blade is 4.5 inches / 115mm in diameter. Its stated specification also includes 1.2mm thickness, 7.5mm specification and a 22.23mm bore. Pasted markdown

What materials can this diamond blade cut?

The packaging identifies concrete, brick, block and masonry as applicable materials. Pasted markdown

Is this diamond blade for dry cutting?

Yes. The packaging explicitly identifies it for dry use only and warns against using it with water. Pasted markdown

What is the maximum speed of the blade?

The packaging states a maximum speed of 13,200 rpm. Pasted markdown

What is the bore size?

The bore is specified as 22.23mm. Pasted markdown

Can I use this blade on an angle grinder?

The product packaging illustrates an angle grinder among the applicable machines. However, users should confirm that their particular machine is compatible with the 115mm diameter, 22.23mm bore and stated speed requirements before installation. Pasted markdown

Can I use this blade with water?

No. The packaging specifically states dry use only and warns against using it with water. Pasted markdown

Is this a 125mm diamond blade?

No. This product is 115mm / 4.5 inches. A 125mm diamond blade is a different size. Pasted markdown

Is this blade suitable for cutting steel?

The supplied product packaging identifies concrete, brick, block and masonry as its applications. It does not identify this blade as a diamond blade for cutting steel, so it should not be selected for steel cutting based on this product information alone. Pasted markdown

Is this a turbo diamond blade?

The product is identified as a FINDER MAX Series Diamond Blade. The supplied packaging does not identify it as a turbo diamond blade, so that description should not be assumed. Pasted markdown

4.5″ FINDER Diamond Blade Buying Checklist

Before purchasing, confirm:

Final Summary

The 4.5″ FINDER MAX Series Diamond Blade is a 115mm dry-use diamond blade designed for compatible cutting applications involving concrete, brick, block and masonry. The blade has a 1.2mm thickness, 7.5mm specification, 22.23mm bore and maximum speed of 13,200 rpm. The packaging also identifies compatible machine types including an angle grinder and circular saw. Pasted markdown

For Ghanaian contractors, masons, construction workers, maintenance teams and other buyers looking for a 115mm diamond blade, checking the complete specification is essential. The 4.5-inch diameter, 22.23mm bore, dry-use requirement and 13,200 rpm maximum speed should all be considered before installation.

CETECH Ghana provides access to construction and industrial products through online and physical offline stores in Ghana, serving individual customers, businesses, contractors, technicians, institutions and commercial or industrial buyers. Bulk supply, industrial sourcing and related supply support can also be considered for larger requirements. Pasted markdown